Golf Republic Forum - Singapore's most active golfing forum.
 
HomeFAQCalendarRegisterLog in

Share | 
 

 Widening gap between clubhead and ferrule for irons

View previous topic View next topic Go down 
AuthorMessage
HitSoft
Junior Golfer
Junior Golfer


Posts : 232
Join date : 2013-05-04

PostSubject: Widening gap between clubhead and ferrule for irons    Sat Jun 07, 2014 11:18 am

Hi guys,

I just noticed that there has been a widening gap between the clubhead and the ferrule on some of my irons. 

Is this a cause for worry i.e I should take it back to Golf House/Acushnet since it's still less than a year old (714 AP2s), or is this just normal for irons over time. Just wondering if it's a manufacturing/quality defect since I don't remember my previous iron set showing this so quickly.

Thanks!
Back to top Go down
HitSoft
Junior Golfer
Junior Golfer


Posts : 232
Join date : 2013-05-04

PostSubject: Re: Widening gap between clubhead and ferrule for irons    Sat Jun 07, 2014 11:25 am

Pictures for comparison:



Back to top Go down
dreamer
Very Active Golfer
Very Active Golfer


Posts : 623
Join date : 2011-03-02
Location : Singapore

PostSubject: Re: Widening gap between clubhead and ferrule for irons    Sat Jun 07, 2014 11:46 am

Does not impact the performance. 
But this does point to quality of workmanship.
Back to top Go down
kyleyann
Senior Golfer
Senior Golfer


Posts : 456
Join date : 2009-10-13

PostSubject: Re: Widening gap between clubhead and ferrule for irons    Sat Jun 07, 2014 12:09 pm

Happens to my irons too. Don't worry too much. You can always push it back up. Besides, I think ferrules are more for cosmetic purposes. They don't actually hold the club head to the shaft.
Back to top Go down
HitSoft
Junior Golfer
Junior Golfer


Posts : 232
Join date : 2013-05-04

PostSubject: Re: Widening gap between clubhead and ferrule for irons    Sat Jun 07, 2014 12:18 pm

dreamer wrote:
Does not impact the performance. 
But this does point to quality of workmanship.
Which is a little disappointing because I had good confidence in titleist when I made the purchase of the 714 AP2s over the mizunos.
Back to top Go down
peace2903
Very Active Golfer
Very Active Golfer


Posts : 889
Join date : 2009-07-02

PostSubject: Re: Widening gap between clubhead and ferrule for irons    Sat Jun 07, 2014 12:35 pm

My 3 wood always has this prob despite bringing to adjust... Almost have to do it 2-3 times a yr. Really a workmanship problem. 
Incidentally, it's also a Titleist 910f。
Back to top Go down
Sponsored content




PostSubject: Re: Widening gap between clubhead and ferrule for irons    Today at 7:15 am

Back to top Go down
 
Widening gap between clubhead and ferrule for irons
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» Gap between ferrule and driver head. Titleist 910d2
» Dynacraft Forged Irons
» Positioning the club face for different irons
» Trail Irons
» rust on clubface

Permissions in this forum:You cannot reply to topics in this forum
Singapore Golf Forum - Golf Republic :: The Clubhouse :: Golf Talk-
Jump to:  
Friends of Golf RepublicFriends of Golf RepublicFriends of Golf Republic
Copyright © 2009 Golf Republic. All Rights Reserved.